Organizers 3D models
Printable storage, cable routing, desk organization, and workshop helpers.
Desk Organizer
Simple design of desk organizer for you to tidy up your desk. You can put 5 debit/credit carts, and hang 3 wrist watches. Extended bar for hanging key chains, or bracelets. Phone stand is there as well, with enough space for you to shove charger underneath of it, as well as it turns 360 degree. Hope this helps even a little bit! This hosted file keeps creator credit and license details.
Pencil Holder
Needed a better Pencil holder, for general purpose use outside of holding my pens and pencils. Added USB slots and a general purpose stand for Tablets, Phones, papers, notes, etc. The stand has an opening for chargers. Center opening for anything you can think of, and everything is angled towards you for comfortable reach. This hosted file keeps creator credit and license details.
Peg Board Plier Holder
This is a remix to add some depth to the hooks for strength because the downloaded design broke. This hosted file keeps creator credit and license details.
Lipo bar for Sullivan high torque starter
This is a 3D printed end cap and lipo bar for a Sullivan high torque starter. The end cap replaces the stock end cap and has provisions for an additional "bar" like the cap that is near the cone. Sullivan intended this design to accommodate left and right handed users. But this end cap utilizes the unused front mount for a bar that will accommodate a lipo. The bar I designed is very simple and has a recess for a battery strap. Please feel free to remix this. You could build a box for 18650's or even nicads. Personally I used one piece of velcro and a battery strap. This hosted file keeps creator credit and license details.
18650 Pack wall mount 1s80p
18650 x4 This hosted file keeps creator credit and license details.
Nespresso sugar box
Boite à sucre Nespresso This hosted file keeps creator credit and license details.
Bar Holder
I made this part to hold what plumbers call "1 inch copper pipe" (near actual 1-1/8). I advise you use a solid structure infill like trianguler and stay away from rectilinear on this print. I am placing this on public domain so that every sentient being may use this at their own discretion. Please give a like if you like this. Computer Aided Designed on Bobcad V30 Computer Aided Manufactured on Simplify 3D V4 Printed on Creality CR-10 Stop Human Trafficking Stop Title IV-D Live long and prosper This hosted file keeps creator credit and license details.
Round Lid & Base
This is a replacement lid and base for a counter-top cotton ball holder. The original was made of metal and rusted, so I designed these as replacement parts. This hosted file keeps creator credit and license details.
Dishwasher Wheel Mount
This is a bracket that I designed to replace a broken one for my dishwasher. The broken mount kept causing the wheel to pop off so I designed my own that is a little beefier to hopefully hold up for a while. This hosted file keeps creator credit and license details.
Desk Cup Holder
Kids have been playing around with tinkercad and wanted me to share what they have drawn This hosted file keeps creator credit and license details.
GoPro Mount for I3 Sunhokey
GoPro mount for videos or timelaps. Temp. 200/45 Enjoy This hosted file keeps creator credit and license details.
Support for 3 Oral-B and 2 glass
Since we all use Oral-b in the family to not have 3 magazines and use them as supports, I invented this that allows me to load one and two supports in two more glasses for children and possibly two head holders. This hosted file keeps creator credit and license details.
Tape Measuring Tol
This handy tape measure add-on allows you to measure and mark with one hand. A 3D printed pencil holder attaches right to the tape measure body, and an arrow aligned with the pencil easily shows where the mark will a land. I made this with Tinkercad . This model will probably work with any tape measure, provided the clearance between the mounting opening and the arrow is wide enough. Grab the STL file below and try it yourself, or follow along in this Instructable . This hosted file keeps creator credit and license details.
Holder for hangers
One of my first models for a 3D printer, maybe someone will come in handy. I made it in the program of TinkerCad This hosted file keeps creator credit and license details.
Stand on the coil
This stand is simple and fast to operate. Nothing has to be dismantled and can be placed anywhere. It does not take place instead when it does not print. This hosted file keeps creator credit and license details.
15mm T-Bracket v2
To Fasten 2pcs of 15x15mm cf square tubes on my quadcopter M4 bolt holes. Version 2, much stronger than first version. This hosted file keeps creator credit and license details.
ZisWorks x39 Control PCB Mount / Labels
A labelled mount for x39 ZisWorks monitors. Best printed transparently and with some added diffusion or other methods of dimming the too-bright RGB status LED. This hosted file keeps creator credit and license details.
Headphone saver
This is a headphone storage thing for earbud headphones This hosted file keeps creator credit and license details.
18560 battery holder for drill adapter
This is the battery holder used for my Drill conversion on youtube, https://youtu.be/7DVDQyouF9E This hosted file keeps creator credit and license details.
Mastech Multimeter Stand
A stand for my cheap Mastech multimeter. Rotate before printing so that one of the sides is flat against the bed. This hosted file keeps creator credit and license details.
Cetus 3D Tool Rack
This is a handy holder for your Cetus 3D stuff. This hosted file keeps creator credit and license details.
Plastic Base for programmable music box
You can buy programmable music boxes rather cheaply, however they are often without a base. This is since it is meant to be installed into a music box, without a box or surface the sound quality of the music box is low. This base will provide a quick way to at least improve your music box sound quality without a box. Just double check that the hole dimensions matches: hole size : 2.55mm hole to hole x dimension: 50.15 hole to hole y dimension: 37.55 You can also use this as a base to build other more complex boxes. This hosted file keeps creator credit and license details.
Spool
This is a generic filament spool model. Definitely NOT for printing. Just a prop for 3D design of spool holders, etc. This hosted file keeps creator credit and license details.
Y-belt holder and tensioner for MK3 and Bear MK2, MK2.5, and MK3
Motivation There's a lot to love about the Prusa printers, but the Y axis belt line is not one of them. A 16T pulley on the motor, a 20T pulley on the idler, and an offset going through the belt holder introduce Z axis forces on your bed as it traverses along Y. These parts allow you to use a 16T idler and get a perfectly parallel belt line, keeping the bed more level as it travels. User RHDreambox designed replacement parts to fix this on the stock MK3, but relies on quality assembly to achieve belt tension. These parts provide adjustment via screws. Built for Bear User pekcitron designed an excellent frame replacement for modern members of the Prusa i3 family of printers. He's also built... This hosted file keeps creator credit and license details.
Digitrax UT Throttle Table Mounts
Here is a project that may have a little narrower focus than some. I made up some holders for the Digitrax UT throttles that mount to the table edge for the grand kids. Sometimes its just a little hard for the wee ones to hold on to the throttles all of the time. This lets do all of the other tasks like putting cars on the track and messing with the switches without having to always hold a throttle. I have a digitrax UT2 and UT4 throttle for the grand kids to use on the . On the UT4 the cable comes out of the top and on the UT2 the cable comes out the bottom. That is about the only difference between the holders. There are mounts for 1/2” and 3/4” thick table tops. The holders just slide on... This hosted file keeps creator credit and license details.
Vertical stand for arduino mega 2560
Hi , This is an arduino vertical stand in 2 parts , very simple and efficient design . Place arduino mega board with force "it's tight for good maintain" in fisrt part (grey) "clic" . And just slide the set in the second part (blue). Done ! (sry for my language) . ID. This hosted file keeps creator credit and license details.
iPhone 6 Plus Pivot Stand
Note: This has not been tested yet Dimenisoned to fit iPhone 6/s Plus. This hosted file keeps creator credit and license details.
Bit Rack
A very simple rack to hold hex bits for screwdrivers and drills. My first design - be gentle. It was designed to fit inside a rack mounted bin from Harbor Freight. This hosted file keeps creator credit and license details.
Filament Spooler for 2020
Filament spooler holder with 2 f623zz This hosted file keeps creator credit and license details.
Flashlight mount ziptae handlebar
Remix from the original source For my flashlight with a diameter of 24.3 mm, I printed the mount from the source file, increasing it to 106.5%. I designed a handlebar mount using tinkercad. Designed for ziptie 3.5 mm, for handlebar diameter 22 mm. This hosted file keeps creator credit and license details.
Torus Marble Track
This is a good toy to demonstrate centripetal acceleration. The torus also makes the marble less likely to become a projectile, compared to a banked track. This could also be used for conservation of energy, as an analog to orbits, because friction and wind resistance are small with the marble. I printed mine with 2 perimeters and 10% infill, with 3 top and 3 bottom layers. I had to scale to 93% to fit on the print bed. This hosted file keeps creator credit and license details.
Egg Holder Hotpoint Ariston Fridge
Egg holder for Hotpoint Ariston fridge. This hosted file keeps creator credit and license details.
business card holder
this small HI BOT is perfect thing to hold your business card, you can scale it up or down depending upon what you intend to use it for. print with 0.2 mm bead, and 25% infill for original size. This hosted file keeps creator credit and license details.
Yet Another Shelf Bracket
Yet another shelf bracket This hosted file keeps creator credit and license details.
Wanhao duplicator i3 v1 spool fix
Everyone here did his own spool holder upgrade- so did i! Be shure, that you hardened printer body with z-braces the original source or similar This hosted file keeps creator credit and license details.
Cable Sleeve
An experiment in cable management. The buttons make it easily adjustable. There are some slices in the print to help with flexibility. This hosted file keeps creator credit and license details.
Pork
This is Pork. my pig cork holder. I remixed it from the cork puppy that EHM Made. This hosted file keeps creator credit and license details.
E3D V6 hotend retainer clip for QuBD One/Two/ThreeUp Printers
QuBD apparently now ships E3D V6 hotends instead of anUbis. I saw E3D in action on a friend's TwoUp and it works so much better than anUbis that I also made the change. E3D has a much bigger groove than anUbis, so the stock mounting mechanism with two screws results in wobbling. I used tape to fill the groove, which worked fine. However, I print a lot and have found that my E3D parts become loose every so often. You can kind of tighten it in place, but it's cumbersome and places strain on the printhead. Removing the hotend doesn't take long, but it's a pain and I could see that my head won't last long if I keep taking these screws out all the time. This retainer clip fixes the wiggle and en... This hosted file keeps creator credit and license details.
Ford Galaxy & VW Sharan Sidelight Removal Tool
For those of you who have tried to remove the sidelight bulb from a Galaxy or Sharan Mk2. You have a little flap in the mudguard that you side open and then try to reach in to unscrew the bulb holder, impossible without the use of a small handed helper, so I made this tool; I can now change bulbs in 15 seconds. Fill your boots. This hosted file keeps creator credit and license details.
Lamp and Lampshade
Made a lamp. Its based on another lamp I had sitting on my desk, but greatly simplified. Printed the shade in "transparent" pla and it seems to provide about the right amount of shade. Bought the other parts needed (bulb socket, cord, and arm to hold the shade) as a kit from hardware store. It looks nice enough that my wife doesn't complain about it being used and displayed. This hosted file keeps creator credit and license details.
400 mm Drone FPV Racing
This is only an prototype of my 400 mm Fpv drone. It mount 4 BR2212 980KV brushless motors and 9 inch prop (at full throttle gives 3 kg of thrust) I am working for the camera mount for an hs1177 If you have any question ask me and I will answer as soon as posible. I hope you like it. This hosted file keeps creator credit and license details.
APPLE TV REMOTE HOLDER WITH SICK GAINZ
Never again lose that pesky Apple TV remote! It is not only a practical decorative piece, but is also a great conversation starter! This hosted file keeps creator credit and license details.
Bracket Structure3D iPad Pro
Bracket structure3D This hosted file keeps creator credit and license details.
gluestick holder
printed by prusa i3. This hosted file keeps creator credit and license details.
Servo mounting frames TGY-225MG & KST DS225MG & MKS DS6125 & Dymond DS 1800 MG
Simple servo mounting frames for use with aluminium housing thin wing servo's. Suitable for servo dimensions: 30mm x 10mm x 35,5mm Turnigy TGY-225MG KST DS225MG MKS DS6125 Dymond DS 1800 MG The models are true to scale. Make sure you print a prototype first. On my 3D printer I had to increase scale of these frames by about 2% to make the servo's fit. Watch out: the screws supplied with these servo's are too long, and will protrude your wing surface. You have to shorten them, or use sufficient thick washers under the screw head. This hosted file keeps creator credit and license details.
chain holder for 420 chains: Skyteam Gorilla / Monkey
You can click this part on your 420 chain so you won't need a third hand to change the chain lock - see pictures. Prints easy without support This hosted file keeps creator credit and license details.
Z-shaft standoff
This is an "add-on" for andreasL's alternate Z-axis for the SmartRap Core. I like my bed to be well supported when at it's lowest position for cleaning so I designed these simple stand-offs that clip on to the 8mm shafts in my printer. They support the bed on both sides quite well. The OpenJSCAD code is straight-forward: function main(){ return difference( union( cylinder({r: 10, h: 5}), cylinder({r: 6, h: 45}) ), cylinder({r: 4.5, h: 45}), translate([0,-4,0],cube({size: [20,8,45]})) ); } This hosted file keeps creator credit and license details.
Cable Carrier ( Cable Chain ) 24x9.5 mm
This is a universal chain you can use for wathever you want . i tried printing 34 links at 0.1 layer thickness 100 % infill printspeed 40 . and it took 18h internal dimensions : 24x9.5 mm verry lose and flexible. i've attached the cat part ( for catia ) if you cant to modify it . This hosted file keeps creator credit and license details.
Proto-Pasta $5 Filament Replacement Spool (For 8mm-9mm shaft)
A replacement spool to change out the extremely minimal and fragile one that comes with Proto-Pasta's $5 filaments. It is made with an 8mm shaft in mind for holding spools. If you have a larger diameter spool holder shaft, measure it and let me know if you want another version. Everything I've done is parametric and easy for me to modify. It takes between 13-14m of filament with around 3.75 hours approximately to print both at 200 micron using Simplify 3D (slightly longer in Cura). You will need to re-orient. This requires a build area of 150mm on x and y for each piece (2 pieces). It also requires three 3m bolts/screws (holes are made deep to accommodate most lengths and made to self-tap w... This hosted file keeps creator credit and license details.
Complete 3D printed Gift Box, Etui
This is a simple 11,5 x 3,5 cm box or etui for whatever fits in. I designed this to be a wrap for a giveaway, it comes complete with hinges and a bit of decor on top. The "print ready" stl contains some additional parts that help to keep things on build plate. After print, the hinges may need a little sanding since the gap between top and bottom hinges is quite on the edge. The needle should fit into pretty smooth. The whole thing is printed in PLA, 0.2mm Layer. Will need a tiny upscale for ABS. Enjoy and dont forget to like, collect or whatever :) This hosted file keeps creator credit and license details.
Printrbot Simple Metal E3D Chimera/Cyclops Mount
A simple mount for an E3D Chimera Hotend to be mounted to a Printrbot Simple Metal. Designed in 123D Design according to Printrbot and E3D design files. This hosted file keeps creator credit and license details.
Dodge Ram Jack Clips
Dodge Ram Jack Clips - My jack had broken clips that hold the handle and crank. So I took dimensions and printed new ones. They work like a charm! I printed these with PLA at 25% fill with support. I tried an early version at 100% fill and it cracked when I mounted it in the jack holder - but that may just be because of wrong dimenstions. If you try it at 100% or with some other plastic, let me know and I'll post that info too! This hosted file keeps creator credit and license details.
SD Card Clip for Rasberry-Pi
Any owner of an early Raspberry-Pi will appreciate how flimsy the SD card holder is. The thin strap across the back of it is easily broken, and snapped off. This design makes a clip that slides onto the Raspberry-Pi and recreates a slot for the SD card. My design is rather cumbersome compared to the elegant solution devised by gould300 ( the original source ). However, because it supports the card beyond the edge of the PCB, it maybe more robust for schools and other places where the R-Pi boards could get rather rough treatment. Not having to be glued on also means any broken clip can easily be replaced. As you might guess I discovered gould300's design after I had print... This hosted file keeps creator credit and license details.
M3D Spool Holder
I really wanted a spool holder that fit in the same space as my M3D printer but didn't bind up. This is the solution I came up with. I'll upload pictures later. This hosted file keeps creator credit and license details.
Camera mount for a Powerzone FPV2600 plane and Contour Roam camera
I made this to mount a Contour Roam HD camera in the front canopy of my Powerzone FPV2600 R/c place. Works great. It saves having to make something to mount on the piece of wood that comes with the plane. It replaces where the pilot would sit. This hosted file keeps creator credit and license details.
Bolt on mount for Fluxient U2 Mini bike light
My first mount was damaged in a car accident, losing one of the O-rings. This modified version attaches to a bike using two M5 bolts. Designed for a Fluxient U2 Mini, but should take any flashlight. An O-ring is required to attach the light to the mount. This hasn't been printed yet, so may not work outright. This hosted file keeps creator credit and license details.
Filament Spool Holder for PrintrBot Play
Filament holder specifically designed for PrintrBot Play frame. Needs set of skateboard bearings. I used these: Skateboard Bearings A standard wooden pencil will work for the crossbar. This hosted file keeps creator credit and license details.
100mm Flat Panel LCD VESA Monitor Mount Spacer
I bought a monitor mount arm (VESA) off of eBay for $20 recently for a debezeled 27" LED monitor I also got off there for $80 or so. The back of the monitor, having been removed, left too much of a gap for the long screws that came with the mount to fit snugly. In order to mount the monitor securely to the back, I printed this little spacer to go in between the two. I think it's around a centimeter and a half thick, (15mm) but you can always just cut it down I guess. Normally I'd attach a photo but I don't want to rip the monitor off the stand, so there's just a rose-gold rendered version :P Hope you find this useful! Thanks! This hosted file keeps creator credit and license details.
CR-10 ESun Spool Bearings
This is a bearing for use with ESun spools that mates to the stock CR-10 spindle. I lubed it up with a bit of oil I had laying around but it seems to work without it. The gaps are fairly tight so you will need to roll it around a bit to wear down any burrs for smooth operation. I printed it at .2 and it worked fine, but I imagine that it would be better at a higher resolution. You may want to print out a cylinder spacer to keep it where you want it. I printed two to match the width of the spool. This hosted file keeps creator credit and license details.
Bluetooth Clip for ATH-M50
I'm going on a trip and I needed a way to easily hold my Bluetooth adapter to my headphones. I bought this adapter . The mount prints in two parts and they use 1.75mm filament to connect the two parts (I'd recommend a little glue to make sure they stay together). It attaches to the headphones with double-sided tape or Velcro. This hosted file keeps creator credit and license details.